Using IsoFlare transducers (point sound source) and an extensive system of BassTrax Tractrix ports, previously used in the F1-8S and F1-10S models, FyneAudio offers loudspeakers capable of, as the manufacturer says, producing Hi-End quality sound from more traditional enclosures. form.
Steering
The crossover, dividing the sound into bands intended for individual drivers (2.5-way), is handmade and subjected to deep cryogenic processing (DCT) in a chamber belonging to Fyne Audio in Glasgow.
Fine Audio F702SP
The technology involves slowly cooling the finished product in the presence of liquid nitrogen to a temperature below -153° and leaving it in the chamber until it reaches room temperature. This results in improved uniformity of connections, reduced internal tensions and increased density of the materials from which the crossover elements are made. Every nuance of sound should be perfectly audible.
Cabling and transducers
The internal cabling is made of PC-OCC cables from Neotech, the crossover uses ClarityCap capacitors, and the signal to the speakers is provided by WBT Nextgen 0703 connectors. Grounding is also available.
In the model Fine Audio F702SP A point sound source is used, a 20 cm IsoFlare driver with a 1-inch magnesium dome tweeter and a neodymium magnet system and FyneFlut upper suspension. The full-range transducer is supported by an 8-inch woofer with a multi-fiber cellulose diaphragm and FyneFlut suspension.
However, in the model Fine Audio F703SP a point sound source was used, a 25cm IsoFlare transducer with FyneFlut suspension, a 3-inch titanium dome tweeter and a neodymium magnet system. In the bass range, it is supported by a 10-inch speaker with a multi-fiber cellulose diaphragm and FyneFlut suspension.
Fine Audio F703SP
Fyne Audio F702SP – technical specifications
• System type: 2.5-way, two-chamber housing, downward-firing bass reflex port with BassTrax Tractrix diffuser
• Recommended amplifier power: (Watt RMS) 30 – 200
• Peak power: (Watt) 400
• Continuous power: (Watt RMS) 100
• Sensitivity (2.83V / 1m): 92 dB
• Nominal impedance: 8 Ω
• Frequency response (typical -6 dB indoors): 28 Hz – 34 kHz
• Transducers: 1 x 200 mm IsoFlare point sound source with FyneFlut suspension, multi-fiber bass-midrange diaphragm, 25 mm magnesium dome tweeter, ferrite magnet system. 1 x 200 mm multi-fiber bass-midrange diaphragm with FyneFlut suspension
• Crossover frequency: 250Hz & 1.8kHz
• Crossover type: bi-wired, low loss, 2nd order low pass, 1st order high pass, deep cryogenic
Fyne Audio F703SP – technical specifications
• System type: 2.5-way, two-chamber housing, downward-firing bass reflex port with BassTrax Tractrix diffuser
• Recommended amplifier power: (Watt RMS) 30 – 250
• Peak power: (Watt) 500
• Continuous power: (Watt RMS) 125
• Sensitivity (2.83V / 1m): 94 dB
• Nominal impedance: 8 Ω
• Frequency response (typical -6 dB indoors): 24 Hz – 34 kHz
• Transducers: 1 x 250 mm IsoFlare point sound source with FyneFlut suspension, multi-fiber bass-midrange diaphragm, titanium dome tweeter with a diameter of 75 mm, neodymium magnet system. 1 x 250 mm multi-fiber bass-midrange diaphragm with FyneFlut suspension
• Crossover frequency: 250 Hz & 850 Hz
• Crossover type: bi-wired, low loss, 2nd order low pass, 1st order high pass, deep cryogenic
Source: EIC
