After talking to Ray on the beach, it’s clear that your next target will be the next Galileo satellite that Blume will launch into space. Drop Ray off at the marked hackerspace and then listen carefully to what he wants from you. Get on your way.
When you arrive at the hangar, hack the panel to the left of the entrance and start the next network bridge puzzle.
Network Bridge Puzzle Galilei Corporation
Use the quadrocopter and fly to the roof, because this is where it starts.
1. Turn the T-piece so that the short side faces the building.
2. Unlocks the locked node and rotates it s0 so that current flows to the next node.
3. Now turn the T-piece from just so that the short end points to the source of the current.
4. Now open the third node and rotate it so that it sends the current down the wire furthest from the building.
5. Unlock the knot and turn the new tee so the short side faces the building.
6. Then open the next knot and turn it so the short end is pointing away from the building.
7. Now turn the T-piece on the right so that the short end is pointing downwards.
8. Now the L-piece on top of the roof once more: Turn it so that the current flows down the left of the two cables.
9. Now open the last encrypted node and turn it so that the current can flow all the way down. Then open the last lock.
Then hack the box below to give Ray access to the surveillance cameras. Then go to the lobby. To the right of the laser barriers you can climb onto a showcase and from there you can get to the first landing. If you already have the ability to use the “Manhunt: Suspect Found” or “Manhunt: Criminal Wanted” ability in the social engineering section, you can burden the security guard behind the laser barrier with it as well. The police will then pick him up and you can freely climb over the frame between the laser barriers.
At the top, sit down next to the door and continue your way with the quadrocopter into the high-security area. Fly to the right and use NetHack sight to find the laptop that contains the access key – you can get in through a hole in the wall a little further up. Then sneak through the door with Marcus and to the right until you come to a stairwell. Here you go all the way to the top. There through the door and onto the catwalk to the tip of the rocket. On the right is a container that you steer towards you. Then jump up and go all the way to the right and then take the container to the railing near the target room. Send your jumper under the laser barrier and inside through the vent to target. Hack the security terminal here and the door will open.
If you haven’t already unlocked the ability to disable the laser lockout, you’ll need to send your jumper drone to the garage for the lift platform from across this hall, hack the fuse terminal there, and then find the fuse terminal on the other side of the hall , which lowers the bollards that separate the two sides. Then you can steer the lift to the other side on the northeast side of the target room – following jumping from the container onto the lift – extend the lift all the way up and climb through a piece of open glass wall to the target. Inside then mod the motherboard and ride back on the container to the rocket to install the motherboard.
Now leave the area the same way back (down the stairs, through the door to the foyer and, depending on whether there is still a guard there or not, jumped over the laser barrier or jumped over the railing from the upper floor. Then leave the area.
Now it’s time to wait for the launch of the rocket. If you want it to continue straight away, you can lie down on the couch in any DedSec HQ to let time pass.
After the start you get to see the world from above. The goal is now to penetrate Blume’s data center in Delaware. Tune into the nearest satellite, then hack into the Blume office in Dublin. Switches to the camera with which you can trigger the network alarm. One technician walks away and the woman makes a phone call. Then you can hack their phone to get the access key. Then you access the computer.
Then one satellite further to the right and hacked into the Dubai server farm. Inside, hack the server on the left for the access code, then use the cameras in the server room to hack all other servers.
Then continue to the next satellite on the right and board the Seoul Power Plant. Choose one of the cameras on the back wall and disable the computers under the desks so that the squares on the big screen turn red. We mightn’t really figure out the exact combination, but it’s not hard to pay a little attention to which computer colors which square from blue to red.
Continue with: Watch Dogs 2: Power to the People, Network Bridge Puzzle !Nvite
Back to: Watch Dogs 2 – Walkthrough, Tips and Tricks
Network Bridge Puzzle Delaware Data Center
One satellite further to the right you can now enter the Delaware data center. Inside, for some reason, you can remotely control a quadrocopter. Fly him to the target and use the camera behind the glass to the control room, hack the target inside and then switch back to the drone.
Most of these puzzles are already more or less solved, only the knots that are still closed have to be opened. Therefore, we focus on the last two pillars:
The pillar at the back right as seen from the control room:
1. Rotate the top tee so the short end is pointing to the right.
2. Unlock the switch below and set it horizontally
3. Turn the T-piece up with the short end.
4. Unlock the left node and rotate horizontally.
5. Unlock the node below, then the one next to it, and once more the one below.
6. Twist the L-piece so the current flows down and open the next knot.
7. Turn all four horizontal lines vertically (“on edge”), turn the upper T-piece with the short end to the left. Then turn the L-piece so that it directs the current to the left.
8. Open the next switch, the short end must be facing up.
9. Now let the L-piece to the right direct the flow downwards.
10. Open the next node, stand it vertical, then place the tee above it so the current flows down to the last node.
11. Decodes the last switch.
The pillar at the back left as seen from the control room:
1. Rotate the lower L-piece so that the current flows to the left.
2. Unlocks the node and then the one that can now be activated further up.
3. This L-piece lets you send electricity to the left.
4. Then turn the T-piece underneath so that the short end is pointing to the left and decode the next switch.
5. Now rotate the bottom L-piece so that it points up and to the left, then the top L-piece, at the very beginning, so that it points up and to the left.
6. The L-piece on the left below the top one must now also point up and to the left.
7. The line must be changed from vertical to horizontal.
8. Then open the switch at the bottom right and finally the next one
You can click through all other server columns more or less without problems and to do something big. Almost all of the switches are in the right position, and if they aren’t, it’s just a twist or two.
Once the power is routed back to the control room, switch back to the camera inside and hack there one last time to start the download.
